EMI Ferrite / Ferrite Core
As the pioneer of EMI Ferrites products, KITAGAWA INDUSTRIES America has wide range of Ferrites core products.
Ferrite Cores are important for ensuring strong electronic signals through cables in environments where EMI (Electromagnetic Interference) can be a problem.
Filtering is an element of EMC design that suppresses conductive noise in conductors such as cables and IC leads. It attenuates or absorbs noise in unnecessary range while allowing only signals at specified necessary frequencies to pass through. Installing the ferrite cores over the affected cables where the current flows increases the impedance and reduces the propagation of noise current due to the magnetization of the ferrite cores. In general the phenomenon of the magnetization of ferrite cores is the process of converting the noise to negligible heat energy and dissipating it.
Using this the method of filtering noise, ferrite cores, sometimes called “Ferrite Beads,” are placed/clipped onto cables in order to suppress high frequency noise levels in electronic signals. Ferrite cores are among the most inexpensive means to reduce EMI noise in an environment involving preexisting electronic cabling. Some ferrite cores require the cable or wire to be wrapped around 6 or 7 times within the core, which is a method called turning, while other ferrite core products simply snap around an existing wire.
As the pioneer of EMI ferrite core products, KITAGAWA INDUSTRIES America has a wide range of ferrite products.
For cable conducted noise the solutions includes: new ferrite “G-Core” series, which offer environmentally friendly materials with cost efficiency, and lower frequency range (KHz range) ferrite cores such as TRM, TRMH, RFC-MA series.
For CPU, IC emissions, cross-talk issues, RFID malfunctions at 13.56 MHz, or gathering magnetic field for devices with NFC (near field communication) technologies, we offer flexible ferrite sheets and ferrite tiles for excellent performance increases.
Ferrite Cores for Cable Noise
KITAGAWA INDUSTRIES America Inc. offers a variety of EMI Ferrite Cores for cable noise solutions on round cables, flat cables, ribbon cables, FPC cables and so on.
These environmental friendly and cost effective G cores come in one piece solid core types, split types that have two halves, and split type cores with plastic casings.
Low Frequency Ferrite Clamp: RFCW-13MA-BK-1PC NEW!
Ferrite clamp that can withstand engine compartment conditions. Excellent low frequency noise suppression (150 KHz~30MHz).
Round Cable Ferrite Cores (2-pieces)
These high-performance ferrite cores for round cables come in three types of materials: nickel-zinc and magnesium-zinc. They are great to clamp onto terminated cables and are available with different types of plastic casings.
Split Toroidal Ferrite Cores With Plastic Housing (GRFC Series)
G Ferrite Core – no nickel and competitvely proced. Employ high-performance ferrites (Nickel-Zinc) effective against high frequency noise.
Split Toroidal Ferrite Cores With Plastic Housing (RFC-H13, RHC−20, RFCK2-20)
Employ high-performance ferrites (Nickel-Zinc) effective against high frequency noise.
Split Toroidal Ferrite Cores with Plastic Housing (Patented) – GTFC Series
High performance Nickel-Zinc ferrite cores for effective common mode EMI suppression.
Split Toroidal Ferrite Cores with Plastic Housing (Patented) – GTFCK Series
Incorporated spring (stainless steel-SUS 304-CSP) insures permanent tight contact of the two-sleeve core halves for consistent performance.
Ferrite Core: Round Cable Ferrite Cores – TFCN Series
Ferrite Clamp for Easily Attachable and Removable by One Hand. Cable guide provides easy cable winding and prevents cable pinching.
Round Cable Ferrite Cores (1-piece)
These high-performance ferrite cores for round cables come in three types of materials: nickel-zinc and magnesium-zinc. They can be easily slid onto non-terminated cables. They come in a variety of sizes and our low frequency (KHz) ferrite cores come with epoxy coating as well.
Sleeve Core, Bead Core (GRI Series)
G Ferrite Core – no nickel and competitvely proced
Toroidal Ferrite Cores Round/Oval Style (GTRE Series)
Ferrite Clamp for Easily Attachable and Removable by One Hand
Ferrite Core: Broad Effect Core – BRE Series NEW!
High-performance, broadband EMC noise suppression core. Amorphous metal core, effective for suppression of conducted and radiated broadband noise from around 1MHz~100MHz.
Flat Cable Ferrite Cores (2-pieces)
These high-performance ferrite cores for flat cables come in two types of materials: nickel-zinc, magnesium-zinc. They come with two pieces or split type and can be easily applied over terminated cables. They come in a variety sizes, and KITAGAWA INDUSTRIES America offers a patented flexible version that is thin, light, and durable.
Thin & Flexible Ferrite Core – FFPC Series
Noise filter with sintered body for FPC which has reduced thickness overcoming the rigid and brittle feature of ferrite core
Split Ferrite Cores For Flat Calbes (GSSH Series)
Split core type for easy assembly on wired or connected cables
Split Ferrite Cores For Flexible Circuits (GFPH Series)
Split core for convenient fitting on pre-wired cables
Split Ferrite Cores For Flexible Circuits (GFPO Series)
Open magnetic circuit structure provides high impedance with close contact on FPC
BCN Series: Split Block Ferrite Cores for Flat Cables (Patented)
Larbor-saving assembly and fixing by combination with plastic clamp. High performance Nickel-Zinc ferrite cores for effective common mode EMI suppression on flat ribbon cables.
Flat Cable Ferrite Cores (1-piece)
These high-performance magnesium-zinc ferrite cores are designed to provide high performance for flat cables. They come as one whole piece in a variety of different sizes to be slid over non-terminated cables.
Solid Ferrite Cores For Flexible Circuits (GFPC Series) NEW!
Suitable solutions for EPC noise problems.
Solid Ferrite Cores For Flat Cables (GSSC Series)
Noise suppression for ribbon cables
Higher magnetic permeability and saturated magnetic density than a ferrite core. Suppresses noise from 150KHz to 30MHz generated by a switching regulator or an inverter.
AF Series: Suitable solution for power line noise
Higher magnetic permeability and saturated magnetic density than a ferrite core.
Soft ferrite core for lead components – GRIP Core NEW!
Natural grip of silicone-rubber covering allows for easy installation. GRIP core can be fixed in place with no adhesive.
Due to higher magnetic flux density, current superposition (current at 20A or less) will not lower the impedance. Resin-coated core to protect cables. Impedance is stable from -40°C~+140°C, with a high Curie temp.
Plastic Holder Options
KITAGAWA INDUSTRIES America Inc. offers plastic holders to keep the two piece split type ferrite core together over the cable.
Plastic Holders For Flat Ferrite Cores (This data coming soon)
Ferrite Tiles and Sheets for Chip/CPU
KITAGAWA INDUSTRIES America Inc. offers EMI ferrite tiles (SD tiles) and flexible ferrite sheets (FFS series) for emission noise and coupling issues caused by CPUs/ICs. The Ferrite sheets also work for RFID malfunctions to correct the magnetic loop emitted so that RFID readers can work properly. Overall they increase the reading range as well by gathering magnetic field to strengthen the signals to read tags and other items. KITAGAWA INDUSTRIES America Inc.’s FFS flexible ferrite sheets are very thin and flexible to be applied into the applications such as RFID, NFC (near field communication), and NFP (near field power) applications.
Flexible Ferrite Sheets
KITAGAWA INDUSTRIES America carries very thin and flexible ferrite sheets used for many applications including EMI absorbing in the low MHz range, RFID, NFC, and NFP applications working at 13.56 MHz.
Flexible Emi Suppression Ferrite Sheet For CPU (FFS Series) NEW!
EMI Flexible Noise Suppression Ferrite Sheet
Flexible Emi Suppression Ferrite Sheet For CPU (FFSX Series) NEW (NFC/RFID)
EMI Flexible Noise Suppression Ferrite Sheet
*Other ferrite material for other frequencies is available upon request.
Ferrite Core Tiles
KITAGAWA INDUSTRIES America Inc.’s standard ferrite tiles are high-performance nickel-zinc flat ferrite materials for EMI absorption or suppression depending on series. They come in a variety of different sizes for various applications.
EMI Suppression Ferrite Tile For CPU (SD Series)
SD Tiles – sintered ferrite tiles for CPU’s high density, high perform
Low Frequency (KHz) Ferrite Cores
KITAGAWA INDUSTRIES America also offers ferrite cores that have high impedance at the KHz range. While TRM and TRMH are one piece types, RFC-MA is a split type to go around terminated cables. TRM and TRMH also come with an epoxy coating. Made with combinations of nickel-zinc and manganese-zinc, they come in a variety of different sizes to fit various round cables.
Ferrite Core: Low Frequency Sleeve Ferrite Cores (TRM Series)
“Mn” ferrite cores, suitable solutions for conductive and radiation noise in low frequency range
Ferrite Core: Low frequency ferrite core with plastic casing – TRCB Series NEW!
Plastic casing prevents ferrite core from cracking and chipping. Suitable for conducted emission from KHz to lower MHz range.
Ferrite Core: Ferrite clamp for low frequency range – MRFC Series NEW!
Effective solutions for suppression of disturbance from switching power supply and motor.
Ferrite Core: Low Frequency Sleeve Ferrite Cores (TRMH Series) NEW!
Most suitable ferrite core for suppressing conductive noise at 1 MHz or less.
Ferrite Core: Low Frequency Split Type Ferrite Cores (RFC-MA Series) NEW!
Ferrite clamp with excellent heat resisitance, effective for prevention of conducted/radiated noise in low-frequency range. Plastic case withstands up to 120C and suitable for suppressing low frequency noise generated by engine control units (ECU), inverters, and motors.